2. 从服务器索引(优先级)(Server Index (Priority))下拉列表中选择一个服务器的优先级 (server priority). 3. 在 Server IP Address 文本框中输入 NTP 服务器的 IP 地址. 4. 选择 NTP Server Authentication 复选框,启用 NTP 服务器的身份验证. 5. 点击 Apply 按钮. 6. 选择 Controller > NTP > Keys...
enable 启用 NTPntp-server x.x.x.x 指定 ntpserver 地址 clock user-timezone CST +8 0 配置时区 配置结束后 exit write memory 保存配置 show ntp 查看设备同步状态日志的时间戳只有在重启 GSS 设备后才能启用新的时区1.6 思科 CS-MARS-100E-K9 上配置 NTP首先确认 NTP SERVER 地址 ,开启 icmp 服务。
首先确认NTP SERVER地址,开启icmp服务。 登陆网络设备,在要同步的网络设备上ping通ntp server。 ping成功后安如下命令键入: enable进入特权模式 config terminal进入配置模式 ntp server x.x.x.x指定ntpserver地址 clock timezone CST +8配置时区 ntp source Vlan xx配置ntp所取的网段属于vlan xx(如果无法看出来属于...
我简单分析了下ntp协议,发现如果自己实现可以用tcp或是udp的方式向ntp服务器端口123(ntp服务端口)发送一些报文,然后接收返回即可。我开始以为报文是任意的,因为以前记得用telnet ip 123也返回了时间字符串(现在觉得可能是记错了啊! )于是有了我的第一次尝试: #!/usr/bin/ruby require 'net/ntp' def get_ntp_...
$> docker exec ntp chronyc sourcestats 210 Number of sources = 2 Name/IP Address NP NR Span Frequency Freq Skew Offset Std Dev === time.cloudflare.com 35 18 139m +0.014 0.141 -662us 530us time1.google.com 33 13 128m -0.007 0.138 +318us 460us Are you seeing messages like these...
o DHCP server Disabled (=off and NOT set as Forwarder!) o Local IP address in subnet of primary router but outside DHCP scope, make sure the used IP address is unique on your network you cannot have duplicates. o Gateway and Local DNS pointing to primary router ...
Support SERVER and BROADCAST working mode; Ethernet port supports 10/100M, full-duplex, half-duplex, supports auto-negotiation mechanism Support user-defined MAC address .NMEA0183 transmits via TCP protocol Compact and easy to install Power consumption is only 1W ...
Starting NINA_NTPClient_Advanced on SAMD_NANO_33_IOT with WiFiNINA using WiFiNINA_Generic Library NTPClient_Generic v3.7.5 Connecting to: HueNet1 NTPClient_Advanced started @ IP address: 192.168.2.98 Using NTP Server 0.ca.pool.ntp.org ***NOT UPDATED*** UTC : 00:00:01 UTC : 0: 0: ...
Thefudgecommand is used to provide additional information for individual clock drivers and normally follows immediately after theservercommand. Theaddressargument specifies the clock address. Therefidandstratumoptions control can be used to override the defaults for the device. There are two optional devi...
ntp peer server2 here is the server config: server1#sho ntp ass address ref clock st when poll reach delay offset disp +~127.127.7.1 127.127.7.1 3 32 64 377 0.0 0.00 0.0 *~y.y.y.y 132.246.168.164 3 109 1024 373 1.3 270852 6.5 * master (synced), # master (unsynced), + selected...